|
Paper Cutting Machine Hydraulic Clamping
BUILT IN OIL TANK IN MAIN MACHINE FRAME
To make good looks,the main frame of castings of machine is designed to work as main stand of machine and hydraulic oil tank. The filters, main hydraulic cylinder and hydraulic oil delivery pump is concealed in this main part.
NEGLIGIBLE PIPE FITTINGS
The Paper Cutting Machine Hydraulic Clamping is provided with a unique MANIFOLD device & all the hydraulic operating valves are directly fitted over the manifold itself.All the pipe fitting is eliminated by use of manifold.Pipe fitting is major cause of oil leakage.
LOW HYDRAULIC PRESSURE
Low Pressure, when the clamp is used to help align the stock, it is operated by a foot pedal & cutting line is checked while the pressure remains low.
HIGH HYDRAULIC PRESSURE
After checking at low pressure when we press the two electric push buttons to make a cut high hydraulic pressure sets down on the paper stock to grip it for cutting accurately.
OPERATION
The Paper Cutting Machine Hydraulic Clamping is operated all through ELECTRIC PUSH BUTTONS OR THROUGH PROGRAMME & transmission of power is through Electro-Magnetic Clutch and brake system.
DRIVE
The machine is provided with a unique oil dipped REDUCTION GEAR BOX for noiseless running with long life.
TWO HANDED CUTTING CYCLE SWITCH
To make cut, you must press both cutting buttons simultaneously till the knife starts. If either one is released or both is released the machine stops immediately.
DOUBLE STROKE PREVENTION
The Paper Cutting Machine Hydraulic Clamping is provided with a unique safety device that prevents double knife strokes, means pressing of both cutting buttons continuously will not allow the knife to come down unless & until it is released & pressed again.
PHOTO ELECTRIC SAFETY GUARD
The Paper Cutting Machine Hydraulic Clamping is provided with photo electric transmitter receiver sensors for safety measures . If anything obstructs the infra red beams, the knife stops immediately. The positive drive of the machine ensures that when the knife is moving up after cutting the stock it stops only at its desired position.
MECHANICAL OVER LOAD PREVENTION
The Paper Cutting Machine Hydraulic Clamping is provided with shear bolts that guards against over loads, they provides full protection on each cut.
GENERAL DESCRIPTION OF PAPER CUTTING MACHINE HYDRAULIC CLAMPING
The cast iron frame has been reinforced for extra strength. It's sturdy.design eliminates all risks of vibration & excessive strain.
The smooth cutting cycle is fast & accurate, even when you're cutting hard material or high stock. Moreover, the knife drive & clamp are dimensioned for heavy duty. Since the drive mechanism runs in an oil bath, lubrication is limited to a single oil change per year, thus reducing maintenance cost.
The fast cutting stroke is very accurate, to the knife carrier guides. All sliding surfaces have been precisely ground, guarantee of dependable precision & long service life.
High pressure ..... Hydraulics are used for precise, automatic clamping. The clamp starts gently & sets dawn softly on the stock. After contact has been established, the clamping pressure is increased automatically to the preset value, avoiding any distortion of the stock.
.... And low pressure, when the clamp is used to help align the stack, it is operated by a foot pedal & clamping pressure adjusted to 40 Kg. approximately to protect the operator.
The back gauge which moves smoothly is guided precisely on a column & side plates length up to knife carrier ensures a right angle cut even at the smaller length of the stock. The hand wheel mechanism provides comfort to the operator for the fine adjustments of the cutting marks,when working in manual mode of programe.
Simple & safe knife change, knife guides provided with the machine, helps removing of the knife easily avoiding any danger to the operator & provision of hand switch locks the mains motor running while process is carried out, avoiding any chances of accidents.
TECHNICAL SPECIFICATION
|
|
Model
|
SMPCMHC 92
|
SMPCMHC 109
|
SMPCMHC 115
|
|
PRICES
|
FOB INDIAN PORT
|
USD 14600=00
|
USD 15000=00
|
USD 15500=00
|
|
Cutting Width
|
mm
|
920
|
1090
|
1150
|
|
Cutting Length
|
mm
|
920
|
1090
|
1150
|
|
Cutting Capacity
|
mm
|
100
|
125
|
125
|
|
Cutting Speed
|
rpm
|
40
|
40
|
40
|
|
Clamp Pressure
|
kg
|
300 to 3000
|
300 to 3000
|
300 to 3000
|
|
Front Table Depth
|
mm
|
585
|
585
|
700
|
|
Side Table Depth
|
mm
|
400
|
400
|
520
|
|
Side Table Width
|
mm
|
590
|
590
|
590
|
|
Machine Width
|
mm
|
2000
|
2590
|
2760
|
|
Machine Depth
|
mm
|
2000
|
2590
|
2760
|
|
Machine Height
|
mm
|
1500
|
1660
|
1660
|
|
Motor Power
|
|
|
|
|
|
Consumption
|
KW
|
4.82
|
4.82
|
5
|
|
Gross Weight
|
kg
|
2500
|
2800
|
3200
|
|
STANDARD EQUIPMENT
|
|
|
Photoelectric safety guard
|
Two knives
|
Two side stock tables
|
|
Two-handed trigger for cutting cycle
|
knife changing kit
|
Complete set of tools
|
Operators manual
|
Motor with electrical equipment for AC
|
|
